Thomas Br.
をテンプレートにして作成
[
トップ
] [
新規
|
一覧
|
単語検索
|
最終更新
|
ヘルプ
]
開始行:
*Thomas Br. [#l370268a]
**1.Field of application [#c4bc71a3]
>The Thomas bridge of U.S. Route 219 crosses the Blackwater River in Tucker County, West Virginia.
**2.Circumstances of repair [#ocdc6a7e]
>This bridge was designed in 1979. In 1986, fatigue cracks were found in the top and bottom un-stiffened girder web gaps. Therefore, retrofit procedures were recommended.
**3.Types of structure [#t158cd91]
>The structure consists of multiple longitudinal girders which support a reinforced concrete deck and transverse cross bracing. The plan and elevation views are shown in [[figure 1>#fig1]],[[2>#fig2]]. The span 1 girders are kinked at the splice to permit a curved roadway. The transverse cross bracing exist between the girders and offset in span 1([[Fig.1>#fig1]]).The transverse cross bracing is bolt connected to transverse connection plates which are fillet weld connected to the girder webs and the girder compression flanges. The transverse connection plates are cut short of the girder tension flanges creating 64mm girder web gaps in the positive and the negative moment regions([[Fig.3>#fig3]]). At the inflection joints, the transverse connection plates are not attached to the girder top and bottom flanges. The structural steel is ASTM A36.
&br;
CENTER:&aname(fig1);&attachref(Thomas1.gif);&br;
&br;
CENTER:Fig.1 Framing plan and girder elevation.&br;
&br;
CENTER:&aname(fig2);&attachref(Thomas3.gif);&br;
&br;
CENTER:Fig.2 Elevation view and transverse connection plate (or stiffener) layout.
&br;
CENTER:&aname(fig3);&attachref(Thomas2.gif);&br;
&br;
CENTER:Fig.3 Transverse cross bracing and transverse connection plates.
&br;
**4.Details of loading [#w2df67b8]
>Fluctuating loads due to vehicles live load.
**5.Description of damage [#c4990c2f]
>Fatigue cracks were found in the top and the bottom un-stiffened web gaps at the transverse connection plate ends.
>Cause of fatigue crack was as follows:
-Out-of-plane distortion which resulted from the differential displacement between the girders.
-The kink structure in the span 1 roadway.
-No positive attachment near the inflection points between the transverse connection plate ends and the girder flanges.
**6.Repair method applied [#u4789b36]
>Repair of parts subjected to cracking were performed by hole-drilling at the crack tips and positive attachment between the transverse connection plates and the girder flanges in span1 and the negative moment regions of the other spans.
&br;
終了行:
*Thomas Br. [#l370268a]
**1.Field of application [#c4bc71a3]
>The Thomas bridge of U.S. Route 219 crosses the Blackwater River in Tucker County, West Virginia.
**2.Circumstances of repair [#ocdc6a7e]
>This bridge was designed in 1979. In 1986, fatigue cracks were found in the top and bottom un-stiffened girder web gaps. Therefore, retrofit procedures were recommended.
**3.Types of structure [#t158cd91]
>The structure consists of multiple longitudinal girders which support a reinforced concrete deck and transverse cross bracing. The plan and elevation views are shown in [[figure 1>#fig1]],[[2>#fig2]]. The span 1 girders are kinked at the splice to permit a curved roadway. The transverse cross bracing exist between the girders and offset in span 1([[Fig.1>#fig1]]).The transverse cross bracing is bolt connected to transverse connection plates which are fillet weld connected to the girder webs and the girder compression flanges. The transverse connection plates are cut short of the girder tension flanges creating 64mm girder web gaps in the positive and the negative moment regions([[Fig.3>#fig3]]). At the inflection joints, the transverse connection plates are not attached to the girder top and bottom flanges. The structural steel is ASTM A36.
&br;
CENTER:&aname(fig1);&attachref(Thomas1.gif);&br;
&br;
CENTER:Fig.1 Framing plan and girder elevation.&br;
&br;
CENTER:&aname(fig2);&attachref(Thomas3.gif);&br;
&br;
CENTER:Fig.2 Elevation view and transverse connection plate (or stiffener) layout.
&br;
CENTER:&aname(fig3);&attachref(Thomas2.gif);&br;
&br;
CENTER:Fig.3 Transverse cross bracing and transverse connection plates.
&br;
**4.Details of loading [#w2df67b8]
>Fluctuating loads due to vehicles live load.
**5.Description of damage [#c4990c2f]
>Fatigue cracks were found in the top and the bottom un-stiffened web gaps at the transverse connection plate ends.
>Cause of fatigue crack was as follows:
-Out-of-plane distortion which resulted from the differential displacement between the girders.
-The kink structure in the span 1 roadway.
-No positive attachment near the inflection points between the transverse connection plate ends and the girder flanges.
**6.Repair method applied [#u4789b36]
>Repair of parts subjected to cracking were performed by hole-drilling at the crack tips and positive attachment between the transverse connection plates and the girder flanges in span1 and the negative moment regions of the other spans.
&br;
ページ名:
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
